Conlux 5 manual

Perform the above steps to confirm that the system is ready for vending. If an abnormality occurs during testing, read this manual again and identify the cause. Based on these two sensing methods, the coin tube full status is sensed. If either of the two sensing methods detects the full status and a coin of the particular type which has been sensed as full is inserted, it will be delivered to the cash box by the separator solenoid.

When the rotation of the motor is transmitted to the gear, payout cam and payout link assembly, the payout link assembly reciprocates back and forth. This motion is also transmitted to the change slide and the payout wiper. The change solenoids activate the change levers to control the motions of the change slides.

Coins are carried by the payout link assembly and drop down when the change slides are activated. The dropped coins are paid out by the payout wiper. Change solenoids are provided for each coin tube, and the solenoids are activated to dispense coins from the associated coin tube. The payout link assembly is activated to move the change slide. The coin carried by the payout link assembly drops down and is dispensed by the payout wiper.

Then all the relevant parts return to the standby status. The coin changer can become dirty from coins, dust, foreign matter, etc. Use mild soap water to remove sticky matter, syrup, etc. Discriminator Removal: 1. Push the latch up. Pull the discriminator toward you. Disconnect the discriminator connector. Remove the discriminator from the housing. Installation: In reverse order. Cassette Tube Assembly Removal: 1. Press the cassette latch down. Pull the cassette tube assy. Installation: Engage the concave portions of the cassette tube assy.

Bottom Cover Assy. Removal: 1. Squeeze the base latch between two fingers and open the bottom cover assy. Lift the bottom cover assy. Release the latch that fixes the base latch. Pull the base latch up toward you to detach it. Pull the bottom cover shafts 1 and 2 out from both sides. Installation: Engage the concave portions of the base latch with the slots on the bottom cover shafts 1 and 2 as illustrated.

Payout Link Assy. Pull the payout link assy. The wiper and change slides 1, 2 and 3 can be removed for cleaning. Installation: Push the payout link assy. Note: Be sure to set the payout link assy. Payout Cam Removal: 1. Pull the payout cams out. Installation: Set the payout cams at the standby positions as illustrated. Note: After any service to the payout area always check the payout of each tube! Center Cover Assy. Hold the center cover assy. Pull the center cover up and release the latch at section B four latches left side panel.

Guide the flat ribbon connector through the slot. Note: Be careful not to damage the latches on sections A and B. Installation: 1. Engage the four left latches first and then the five right latches. Note: Be sure that the latches on sections A and B are firmly engaged. Tube-full Lever Removal: 1.

Pull the tube lever shaft out. Then release the three tube-full levers. Installation: Be sure the shaft is aligned properly. Insert the tube lever shaft until it is firmly locked. See the figure. Release the latch. Gear Base Assy. Unplug the three connectors. Release the latch on the rear panel and detach the assembly.

Engage the latch on the rear panel. Plug in connectors and guide the harness back in place. See the Figure 9. Note: The harness should be guided very carefully in the exact same way as before the removal. To ensure this, be sure to memorize how the harness is set before removal.

If improperly set, it may cause abnormal stress and damage to parts. Change Lever and Change Solenoid Removal: 1. Cut the harness tie wrap on the back of the gear base assy. Remove two M3x8 screws. Remove the harness. Before removal, memorize how the harness is set so that you can properly reinstall it later.

Detach the change solenoids and the change levers. Note: When you detach the change solenoids, the associated change levers, plungers, and springs are also removed. Keep them together. Do not mix them up! Insert the plungers of the change solenoids into the slots of the change levers. Install the harness properly in place as it was before removal.

See the Figure Empty Switch Assy. Before removal, memorize how the harness is guided so that you can properly reinstall it later. Release the right and left latches and pull the empty switch assy. Install the harness properly in the same place as before removal. Bundle the harness and fasten it with the tie wrap.

Carrier Switch Assy. If the vending machine has a bill validator , connect the. MDB harness coming from the coin mechanism to the bill. If there is no bill validat or, connect. T uck any excess length of harnessing inside the machine. Make sure no harness is pinched or trapped when the coin. Now you may switch ON the po wer to the vending. This document contains information for installing the. It mounts on.

The operating voltage of a MEI Conlux coin mechanism is. The label is located on. Weight 3. Rated Operating V oltage Voltage: 34v d. Check the alignment of the coin input chute and cashbox. Insert some coins to check that they enter the coin. Most machines allow you to adjust the return lever, coin. Align, adjust, and test as necessary to ensure coins are. If the vending machine has a bill validator, connect the. MDB harness coming from the coin mechanism to the bill.

If there is no bill validator, connect. Tuck any excess length of harnessing inside the machine. Make sure no harness is pinched or trapped when the coin. The coin mechanism can be ordered with one of two. The cassette type will be recognized automatically by the. You can load the coin cassette using either of these two. Remove the cassette. Place it front down on a firm. Open the back by pinching the two tabs together.

Fig 1.